Freedom in all dimensions.

Flexible stone
Delap.

flexible stone

How to install Delap flexible stone

Installation on all surface flexible stone

    We're looking for dealers!

    Do you want to work with us? Please read our terms of dealership first.

    Insulation

    Polystyrene foam EPS

    Installation of flexible stone on polystyrene foam EPS

    Polystyrene priming is not necessary.

    Tiles can be glued directly on the surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Windproof

    Installation of flexible stone on windproof plate Izoplaat

    Appearance. Thick plates of thin pressed wood fibers treated with paraffin. The front side plate is marked with green paint.

    Modern eco-friendly insulation for frame and log homes. The ideal option for use with tile Delap.

    Do not need to be primed  wind protection boards

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Extruded

    Installation of flexible stone on extruded polystyrene XPS

    Appearance: Very dense finely porous plate insulation

    Before installing the tiles of Delap on the surface  XPS, it is necessary prepare:

    1. The surface of the heater clean up  coarse sandpaper and then coat adhesion primer.
    2. Apply the mixture to the base of the plaster layer, then paste reinforced fiberglass mesh
    3. After drying, the base layer of plaster, it is recommended that primed penetrating primer and you can install the tiles Delap.
    4. Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Mineralwool

    Installation of flexible stone on mineralwool

    Appearance. Thick plate of pressed thin stone fibers gray-green color. Packed in a thermo-shrink membrane.

    1. Apply the mixture to the base of the plaster layer, then paste reinforced fiberglass mesh
    2. After drying, the base layer of plaster, it is recommended that primed penetrating primer and you can install the tiles Delap.
    3. Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.
    4. Grouting can serve the same adhesive

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Other bases

    The base from the brick

    Installation of flexible stone Delap on brick

    Preparation of the surface. The main task — to ensure adhesion (ability to stick). For this, the surface should necessarily be processed adhesion primer.

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    The base of concrete

    Installation of flexible stone Delap on concrete bases

    This group consists of concrete surfaces, concrete blocks, strip foundations, as well as any non-porous surface of the concrete with a variety of fillings, including slag concrete, expanded clay. Concrete - the perfect base for any facade tiles, including Delap.

    Surface preparation. Pure concrete no needs priming. Before installation, make sure the concrete surface has no oil stains and dirt. Removed dirt - mechanically. Dust from the surface of the concrete can be washed off with water. Recommend to cover the wall penetrating primer.

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    The base from the timber

    Installation of flexible stone Delap on a log

    A Log. On the wall of the timber must be mounted leveling wooden frame of the bar section 50x50 cm. This will help align the plane of the wall.

    Mounting tile depends on the type of the selected surface to the carcass.

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    The base from the other timber

    The base from the other timber

    Wooden wall. The main task — to form on a wooden wall a flat stable surface on which to glue the tiles.

    Thermal insulation. Optimum insulation for houses of timber is the insulation plate. It is homogeneous with the wall plate from the wood fibers, It is both insulation and wind protection and the basis for tile Delap. If the task is not put insulation, it is possible to install a vertical lath any suitable plate (flat slate, DSP, OSB).

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    The base of cellular concrete

    Installation of flexible stone Delap on cellular concrete, aerated concrete

    Appearance. Light gray blocks of porous foamed concrete in different ways.

    Preparation of the surface. Cellular concrete is porous and draws water from tile adhesive, dramatically reducing its quality. The main task - to eliminate absorbency. To do this, the primed surface in two stages.

    Before priming should make sure the concrete surface has no oil stains and dirt. Grease solvent removed dirt - mechanically. Dust from the surface of the concrete can be washed off with water.

    Tiles can be glued directly on the surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Frame walls

    Oriented strand board OSB

    Installation of flexible stone Delap on OSB

    OSB (oriented strand board) plate is made of several layers of pressed wood chips. Moreover, these layers are arranged at 90 degrees to each other. The surface of the plates treated with paraffin.

    Surface preparation. Plate consists of wood chips, top coated with paraffin. Thus this absorbent OSB plate surface with low adhesion. Dyes contained in it can tread through the glue and paint the seams. Moreover, plates are deformed to humidity changes. To eliminate the negative impact of these factors need to do the following:

    1. Covering surface penetrating primer. It will eliminate the moisture absorption of the tile adhesive.
    2. Covering surface adhesion primer. It will provide a rough surface.
    3. Seams between the plates should be strengthened ribbon serpihan. Tape and profile can be put on the tile adhesive.

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Fiber cement

    Installation of flexible stone Delap on fiber cement

    Fiber cement panels are thick enough, so do not gain moisture and almost not deformed oscillation humidity. These materials - the ideal solution for the outer skin of a frame house tile Delap.

    Appearance. Very dense homogeneous sheets of gray color

    Surface preparation. The plate has a normal adhesion and should be processed only penetrating primer.

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Cement particle board DSP

    Installation of flexible stone Delap on Cement particle board DSP

    Slabs of gray color from concrete with a light filled sawdust. Inexpensive and practical building material.

    Surface preparation. Primed sheets penetrating primer

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Fixed timbering

    Formwork Durisol

    Installation of flexible stone Delap on the formwork Durisol

    Covering surface penetrating primer

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP

    Shuttering Velox

    Installation of flexible stone Delap on the shuttering Velox

    Covering surface penetrating primer

    Tiles can be glued directly on the primed surface using any high-quality tile adhesive for outdoor and indoor use.

    Grouting can serve the same adhesive.

    Warning! Delap tiles may only be used for mantels or furnaces if the laying base is never heated above 60°. If a possibility of overheating exists, the base must be pre-cladded with magnesia cement boards prior to tile installation.

    Magnesia cement boards are non-flammable and can withstand temperatures of up to 1200°C. They have a fire-resistance rating of A and a thermal compression ratio of less than 1%. Thanks to these properties, magnesia cement boards can be used for the manufacturing and lining of mantels and furnaces.

    Warning! Areas prone to water absorption must be treated with special waterproof acrylic materials. This rule applies to all construction work, not only to projects involving Delap stone or similar products. Waterproof materials are suitable for construction, repair and maintenance work. They ensure water-resistance of structures and insulation. By using waterproof materials you ensure that concrete and brick structures (or other types of structure) are protected from penetration by water or other harmful substances (salts, alkalis, oils, solvents, etc.). This is an important step to remember in base preparation process in any building or structure. Keep in mind that foundations and facades always start deteriorating from the inside out, not the other way around!

    Warning! Before cladding structures with any type of base (thermal insulation, support base, framework or permanent forms) ALWAYS consult the base manufacturer first, since every base type (thermal insulation, support base, framework or permanent forms) has its own qualitative and resistance properties as well as application conditions. Only the manufacturer can provide you with the most reliable information about cladding using either Delap products or any other materials. By doing so, you will ensure the highest quality of installation, compliance with the manufacturer’s requirements for the base layer and a long service life for your cladding.

    The instructions available on the Delap website for all types of base layer are for reference only!

    Consult the manufacturer of the base layer first!

    THANK YOU FOR CHOOSING FLEXIBLE STONE BY DELAP